Soluble Ruthenium Phthalocyanines as Semiconductors for Organic Thin‐Film Transistors

Soluble Ruthenium Phthalocyanines as Semiconductors for Organic Thin-Film Transistors

Ruthenium phtalocyanines (RuPcs) possess distinct photoelectronic properties and a broad synthetic scope allowing for highly tuneable molecular designs, making them promising candidates as organic semiconductors in OTFTs. However, RuPcs have been underexplored in this field, and more studies are needed to provide basic insight into their potential. Herein, two novel RuPc derivatives were synthesized and implemented in OTFTs displaying p-type device operation.


Abstract

Ruthenium phthalocyanine (RuPcs) are multipurpose compounds characterized by their remarkable reactivity and photoelectronic properties, which yield a broad synthetic scope and easy derivatization at the axial position. However, RuPcs have been underexplored for use in organic thin-film transistors (OTFTs), and therefore new studies are necessary to provide basic insight and a first approach in this new application. Herein, two novel RuPc derivatives, containing axial pyridine substituents with aliphatic chains (RuPc(CO)(PyrSiC6) (1) and RuPc(PyrSiC6)2 (2), were synthesized, characterized, and tested as the organic semiconductor in OTFTs. RuPc thin-films were characterized by X-ray diffraction (XRD), and atomic force microscopy (AFM) to assess film morphology and microstructure. 1 displayed comparable p-type device performance to other phthalocyanine-based OTFTs of similar design, with an average field effect mobility of 2.08×10−3 cm2 V−1 s−1 in air and 1.36×10−3 cm2 V−1 s−1 in nitrogen, and threshold voltages from −11 V to −20 V. 2 was found to be non-functional as the semiconductor in the device architecture used, likely as a result of significant differences in thin-film formation. The results of this work illustrate a promising starting point for future development of RuPc electronic devices, particularly in this new family of OTFTs.

High Conductivity and Rate Capability of NaNb13O33 Wadsley–Roth Phase as a Fast‐Charging Li‐Ion Anode

High Conductivity and Rate Capability of NaNb13O33 Wadsley–Roth Phase as a Fast-Charging Li-Ion Anode

The NaNb13O33 Wadsley–Roth structured phase is studied for enabling fast charging in Li-ion batteries. The material exhibits good lithium intercalation capacity of 233 mAh/g corresponding to Li15NaNb13O33 and rate capability. Multiple peaks are observed in the differential capacity plot indicating the formation of two-phase regions during intercalation of lithium. In comparison to widely studied TiNb2O7, NaNb13O33 shows faster Li-ion diffusivity particularly at high states of lithiation.


Abstract

The synthesis and electrochemical insertion of lithium into the Wadsley–Roth NaNb13O33 phase is studied. Lithium intercalation to form LixNaNb13O33 reaches a value of up to x~15, between 3.0 and 1.0 V vs. Li+/Li at a slow cycling rate, a capacity of 233 mAh g−1. Within this voltage window, two sharp peaks and one broad peak are observed in the differential capacity plots of lithium intercalation suggesting multiple two-phase regions. High Li-ion conductivity and rate capability was demonstrated. The lithium diffusion constant is about an order of magnitude greater than TiNb2O7. The average voltage is about 1.6 V and its high-rate capability makes NaNb13O33 potentially useful as an anode in a fast-charge Li-ion battery application.

Exploring the Synergistic Effects of Dual‐Layer Electrodes for High Power Li‐Ion Batteries

Exploring the Synergistic Effects of Dual-Layer Electrodes for High Power Li-Ion Batteries

A Li-ion battery electrode architecture which uses two different active materials in a layered configuration is investigated. The results surprisingly show that layered electrodes are superior to their blended (mixed) counterparts during high-rate (dis)charge. The mechanism of this synergistic effect is elucidated using a newly minted synchrotron fluorescence technique to map the concentration of Li+ throughout an operating cell.


Abstract

The electrification of the transport sector has created an increasing demand for lithium-ion batteries that can provide high power intermittently while maintaining a high energy density. Given the difficulty in designing a single redox material with both high power and energy density, electrodes based on composites of several electroactive materials optimized for power or capacity are being studied extensively. Among others, fast-charging LiFePO4 and high energy Li(Ni x Mn y Co z )O2 are commonly employed in industrial cell manufacturing. This study focuses on comparing different approaches to combining these two active materials into a single electrode. These arrangements were compared using standard electrochemical (dis)charge procedures and using synchrotron X-ray fluorescence to identify variations in solution concentration gradient formation. The electrochemical performance of the layered electrodes with the high-power material on top is found to be enhanced relative to its blended electrode counterpart when (dis)charged at the same specific currents. These findings highlight dual-layer lithium-ion batteries as an inexpensive way of increasing energy and power density of lithium-ion batteries as well as a model system to study and exploit the synergistic effects of blended electrodes.

Preparation of 3‐D Porous Pure Al Electrode for Al‐Air Battery Anode and Comparison of its Electrochemical Performance with a Smooth Surface Electrode

Preparation of 3-D Porous Pure Al Electrode for Al-Air Battery Anode and Comparison of its Electrochemical Performance with a Smooth Surface Electrode

3D-porous and smooth surface anodes for the Al-air battery: Al electrodes were produced with smooth and porous surfaces by salt casting. LSV analysis showed that the current density of the porous electrode was three times higher. EIS analysis gives lower charge transfer resistance for the Al-porous electrode. The power density of the Al-porous electrode was approximately 42 % higher than that of the Al-smooth electrode.


Abstract

This study compared the electrochemical performances of porous surface electrodes obtained by the salt casting process against a smooth surface electrode. Potentiodynamic polarization test, linear sweep voltammetry (LSV), and electrochemical impedance spectroscopy (EIS) tests of porous and smooth Al electrodes were performed using 0.5 M NaOH solution. According to the Tafel analysis, the Jcor value of the Al-porous electrode was measured as 3.23 mA cm−2, which is approximately 55 % higher than the Al-smooth electrode. The Ecor value was more negative for the Al-porous electrode. Results of the low charge transfer resistance (2.2 Ω) of the Al-porous electrode compared to the Al-smooth electrode (2.8 Ω) concluded that the porous surface was increased the current density by increasing charge transport due to higher surface area. The galvanostatic discharge tests of the electrodes were carried out in an Al-air battery test cell using a graphite carbon air cathode. As a result, the power density of the Al-porous electrode was approximately 42 % higher than the Al-smooth surface electrode.

Geopolymer Based Electrodes as New Class of Material for Electrochemical CO2 Reduction

Geopolymer Based Electrodes as New Class of Material for Electrochemical CO2 Reduction

Geoploymers for CO2 reduction: Geoploymers offer great potential for reducing CO2 emissions in the construction sector by replacing ordinary cement. Here, we successfully functionalized a geopolymer with tin and applied the hybrid material as an electrode for CO2 electrolysis. The results show current efficiencies of up to 14 % for formate production.


Abstract

To achieve a successful transition to a sustainable carbon and energy management, it is essential to both reduce CO2 emissions and develop new technologies that utilize CO2 as a starting substrate. In this study, we demonstrate for the first-time the functionalization of geopolymer binder (GP) with Sn for electrochemical CO2 reduction (eCO2RR) to formate. By substituting cement with Sn-GP, we have merged CO2 utilisation and emission reduction. Using a simple mixing procedure, we were able to obtain a pourable mortar containing 5 vol. % Sn-powder. After hardening, the Sn-GP electrodes were characterized for their mechanical and CO2 electrolysis performance. In 10 h electrolyses, formate concentrations were as high as 22.7±0.9 mmol L−1 with a corresponding current efficiency of 14.0±0.5 % at a current density of 20 mA cm−2. Our study demonstrates the successful design of GP-electrodes as a new class of hybrid materials that connect eCO2RR and construction materials.